Recycled Tea Cup Bird Feeders

SUPPLIES FOR YOUR BIRD FEEDERS:

* Stencils

* Colorful teacup and saucer

* Ruler

* Marking pen

* Drill and 1/4-inch masonry drill bit

* Sandpaper (fine-grit)

* Acrylic paints in colors of your choice

* Artist's brushes: 1/2-inch flat, #0 liner

* Flat sponge (to make stamp, if desired)

* Buttons (if desired)

* 36-inch-long 1/4-inch threaded metal rod

* 33-inch-long copper tubing with a 1/4-inch-wide opening

* 3 stainless-steel nuts with 1/4-inch-wide hole

* 3 stainless-steel washers with 1/4-inch-wide hole

* Crafts foam (for spacer)

* Hole punch

* Polyurethane clear exterior spray finish

* Platinum Bond Patio & Garden Adhesive

* Birdseed

Instructions:

1. Select stencils to design your Bird Feeders with.

2. Prepare the cup and saucer. Using the ruler and the marking pen, measure and mark the center of the cup and saucer. Carefully drill a hole in the center of both pieces. Sand the surfaces of the cup and saucer to roughen the finish, and wipe or wash off all the dust (this will help the paint adhere). Using the 1/2-inch flat brush, base-coat each piece with acrylic paint; let the paint dry. Repeat with a second coat, if necessary.

3. Paint the designs. Using the stencils you have selected. Or paint free-form shapes in the colors of your choice with the 1/2-inch flat brush. Add details or outline each stencil pattern with a contrasting color and the #0 liner brush. Paint then let the paint dry. Spray all surfaces with two coats of clear spray finish. Button Flower: Cut a flower shape from a flat kitchen sponge to make repetitive flower shapes. Wet the sponge and squeeze it dry; and then brush one surface with paint. Press the sponge onto the base-coated surfaces of the cup and saucer to create the design. Add outlines and details with the #0 liner brush; let the paint dry. Paint the leaves and let dry.

4. Glue buttons to the centers of the flowers. Spray all surfaces with two coats of polyurethane clear finish.



CUP AND SAUCER

5. Assemble the bird feeders. Note: Make spacers by cutting circles from crafts foam and punching holes in the center. Add the individual parts as follows.

Insert the threaded metal rod through the copper tubing. Place a nut at one end of the metal rod but do not tighten it until all pieces are assembled.

At the other end of the rod, place a nut and a washer, then a foam spacer.

Next, place the drilled saucer, then a large circle of crafts foam cut to the same diameter as the bottom of the cup.

Place the teacup on the threaded rod, then a foam spacer, a metal washer, and finally, the metal nut.

Carefully tighten the nuts on the end to create a firm fit. Push the rod into the soil and fill the teacup with birdseed.

Bumblebee Trim for your Bird Feeders:

Add a bee to your bird feeder for an extra touch. The glass-bead body and head and the wings made from screen wire are weatherproof for outdoor use, but you'll probably want to make extras to stick into houseplant pots or use as whimsical napkin rings or lamp finials.

A flighty bumblebee makes a novel trimming for this whimsical bird feeder.

What You Need:

* Bee wing pattern made from cardboard or a stencil.

* Beads: 1-inch-long elongated bead (for body), 1/2-inch round bead (for head), assorted small beads (for antennae and wire).

* 16-inch-long piece of 20-gauge copper beading wire.

* 3x3-inch piece of aluminum screen wire.

* Tulip Dimensional Paint: silver.

* Platinum Bond Patio & Garden Adhesive.

* Needle-nose pliers.

* Heavy-duty scissors.

Instructions:

Bee wing pattern

You also can embellish other garden and home projects with this playful bee.

1. Make a pattern the shape of 2 wings using cardboard.

2. Cut two 3-inch-long pieces of wire, reserving the remainder. Thread both pieces through the two large beads to make a body and head; separate the wires, adding small beads for the antennae, and then curl all four ends with the needle-nose pliers.

3. Using the pattern, cut two wings from aluminum screen wire. Outline the curve of each wing with silver fabric paint to form raised edges; let dry. Bend the cut edges of the wings 1/8-inch toward the underside and glue them to the body.

4. Thread small beads onto the remaining wire, curl one end, coil the wire around a pencil to make a spiral, and insert the other end into the body; glue it in place.

Return to Garden Crafts from Bird Feeders